TorchButton v1.5 per HTC

Cab per trasformare il vostro htc Pro e raphael in una torcia :pioneer 1420:

ecco i dati (in inglese)

.----------------------------------------------------------------------
| TorchButton, v1.5
}----------------------------------------------------------
|
| A simple application built for the HTC Raphael (HTC Touch Pro) to enable
| the flashlight of the camera application. Reported to work on Xperia and
| the US/Sprint version of the Touch Pro as well.
|
| Usage:
| When the program starts, the flashlight is turned on. It will keep the
| light on for 60 seconds (configurable in registry). You can turn the light
| off earlier by starting the program again. This applies to all modes of the
| application.
|
| Modes:
| TorchButton has 5 modes so far. Each one explained in short:
|
| Normal: Simply enable the flashlight until the application is started again or
| the configurable timeout occurs (60 seconds by default). This mode
| can be used for a prolonged period. I have only tested it up to 5 minutes
| though.
|
| Bright: The Bright mode is exactly the same as the Normal mode, with the only
| difference being that the LED is more bright. This mode is equal to the
| short moment when you make a photo with flashlight on. Note that this mode
| does stress the LED and should not be used for prolonged periods. I have
| used this up to a minute without problems.
|
| Blink: The Blink mode turns the LED on and off in specific intervals that you
| can configure in the registry. An example of usage is the bike light.
|
| SOS: This is extensive mode that supports sending custom morse code. The text
| to be sent via morse code signals can be configured in the registry. This
| defaults to "sos ", thus the SOS name for this mode. NOTE that the flashlight
| timeout does NOT interrupt a text. It checks if the timeout occurred when it
| starts over again and quits when it reached the timeout.
|
| PTT: The Push-To-Talk/Torch mode. When you device has a key you can map to 'hold',
| you can use this feature to keep the light on as long as the key is pressed.
| The AT&T Fuze is one of those devices with a PTT button.
|
| Configuration settings:
| All settings can be configured via the Registry. All values can be found under
| the HKLM\Software\TorchButton\ key. An up-to-date list of configuration settings is
| presented below. Note that they are case-sensitive.
|
| FlashlightTimeout (DWORD), default 60. In seconds.
| Configures the timeout after which the application should automatically stop. This
| timeout applies to all variants.
|
| blinkTimeOnInMs (DWORD), default 250. In milliseconds.
| When using blink mode, determines how long the led should stay on.
|
| blinkTimeOffInMs (DWORD), default 250. In milliseconds.
| When using blink mode, determines how long the led should stay off before turning
| on again.
|
| sosText (SZ), default "sos ". Textual.
| When using SOS mode, determines the text to send with morse code. Supported
| characters are a-z, 0-9, comma (,) and period (.). Any non-recognized characters
| are simply ignored. A space character inserts a pause of 7 units. This text may be
| up to 8KB.
|
| sosUnitTimeInMs (DWORD), default 100. In milliseconds.
| When using SOS mode, this determines the unit time that serves as base for the
| various timing. The unit time is the same as how long a "dot" should last.
|
| brightResetTimeInMs (DWORD), default 750. In milliseconds.
| The bright mode uses a mechanism to keep the LED on the mode that is normally only
| used when making a picture with flashlight. A safety in the driver prevents this
| mode from being active too long. I've worked around it by quickly re-enabling the
| bright LED. On some devices this reset time should be shorter.
| NOTE: Set this to 100 when you have the Alltel Touch Pro.
|
| History:
|
| v1.5 (2009-04-28)
| - Added PTT (Push-To-Torch) mode. Probably only useful for devices that have the PTT button,
| such as the AT&T Fuze.
| - Added brightResetTimeInMs registry setting for owners of the Alltel Touch Pro. They need to
| set this value to 100 for bright mode to work properly.
|
| v1.4 (2008-11-29)
| - Fixed 'sos' mode. It now properly uses a single configurable unit time to calculate
| other intervals.
| - Updated 'sos' mode. You can now configure a text to be sent via morse code in the
| registry. Check configuration part of the readme for more info.
| - Removed old 'sos' registry settings and replaced them with new ones.
| - Increased default flashlight timeout from 30 to 60 seconds.
| - Changed default 'blink' time to 250ms for both on and off.
|
| v1.3 (2008-11-13)
| - Added 'blink' feature. Registry configuration options:
| - blinkTimeOnInMs (DWORD), default 500. Configures the time the LED is on.
| - blinkTimeOffInMs (DWORD), default 500. Configures the time the LED is off.
| - Added 'SOS' feature. More like a 'morse code' feature though. You can set any
| morse code to be signalled in the registry. Options:
| - sosCode (SZ), default " ...---...". Configures the morse code to signal.
| - sosDotTimeoutInMs (DWORD), default 200. Configures 200ms LED on, and 200ms LED off for ".".
| - sosDashTimeoutInMs (DWORD), default 400. Configures 400ms LED on, and 400ms LED off for "-".
| - sosSpaceTimeoutInMs (DWORD), default 1000. Configures 1000ms pause when processing space " ".
| - New shortcuts are added for those features.
|
| v1.2 (2008-11-09)
| - Enlarged maximum timeout override from 300 seconds to 86400 seconds (a day).
| - Added 'bright' feature. Note that the light may flicker almost unnoticably
| every 750ms, can't help that. :)
|
| v1.1 (2008-09-01)
| - Added ability to override default timeout value (in seconds) stored in
| HKLM\Software\TorchButton\FlashlightTimeout (DWORD).
|
| v1.0 (2008-08-31)
| - Initial version
|
}-------------------------------
|
| Author: Martijn Stolk


Download:

Codice PHP:

---

http://www.megaupload.com/?d=S0A7VYOG 


---